
AUTOONE 9006/HB4 LED Bulbs, 70000LM 1200% Ultra Bright, R...
$26.99
Buy on Amazon →
Used for: Fog Light Bulb Front
Used for: Fog Light Bulb Front
Used for: Fog Light Bulb Front
Used for: Headlight Bulb High Beam and Low Beam
Used for: Back Up Reverse Light Bulb
Used for: Brake Light Bulb, Tail Light Bulb Outer
Used for: Center High Mount Stop Light Bulb, Tail Light Bulb Inner, Courtesy Light Bulb, Interior Door Light Bulb, Map Light Bulb
Used for: Center High Mount Stop Light Bulb, Tail Light Bulb Inner, Courtesy Light Bulb, Interior Door Light Bulb, Map Light Bulb
Used for: License Plate Light Bulb, Parking Light Bulb
Used for: License Plate Light Bulb, Parking Light Bulb
Used for: Side Marker Light Bulb Front, Turn Signal Light Bulb Front
Used for: Side Marker Light Bulb Rear
Used for: Turn Signal Light Bulb Rear
Used for: Dome Light Bulb, Trunk or Cargo Area Light
Used for: Glove Box Light Bulb
If you need bulb sizes for the 2006 Toyota Sequoia, this page organizes the most common lighting positions in one place. It helps you verify the correct bulb size by location, so you can match the right part for headlights, tail lights, interior lights, and other exterior lamps without guessing.
The 2006 Toyota Sequoia uses different bulb types depending on the lighting position, and some trims or lighting packages may vary by market and body style. Use the bulb chart below to confirm the fit for each lamp before you buy replacement bulbs, especially if you are changing more than one light at the same time.
For best fitment, always compare your vehicle’s installed bulb with the listing for the exact lighting position, since trim level, package content, and regional differences can change the application. This is especially important when switching between halogen and LED replacements, because an aftermarket LED may fit the socket but still require the correct beam pattern, polarity, or additional hardware to work properly. If you are doing an LED conversion on fog lights, turn signals, or interior lamps, check whether resistors or compatible flashers are needed to avoid hyperflash or warning issues. Before ordering, it is smart to inspect the old bulb, confirm the base style, and verify the socket shape on your specific Sequoia so you do not end up with the wrong part.
The high beam and low beam headlight bulb size listed for the 2006 Toyota Sequoia is 9003. This page is organized by lighting position so you can confirm the correct bulb for the headlight assembly before replacement.
The front turn signal light bulb size is 3157A. If you are replacing both sides, check each socket and bulb condition before installation to make sure the fit is the same on your specific vehicle.
The rear turn signal light bulb size listed for the 2006 Toyota Sequoia is 7440A. This is separate from the brake and tail light bulbs, so it is important to match the bulb to the correct rear lamp position.
The brake light bulb size is 7443R. The same bulb size is also listed for the outer tail light bulb position, so verify the exact lamp location before ordering.
The outer tail light bulb size for the 2006 Toyota Sequoia is 7443R. This page helps you separate the outer tail lamp from the inner tail lamp and other rear lighting positions.
The inner tail light bulb size is 194 or 7441, depending on the application listed for that position. Always confirm the installed bulb and the lamp location on your Sequoia before purchase.
The license plate light bulb sizes listed are 168 and 917. Either size may appear depending on the specific lamp setup, so checking the installed bulb is a good idea before buying replacements.
The dome light bulb and trunk or cargo area light bulb are both listed as DE3175. These interior bulbs are often easy to replace, but the exact lamp housing should still be checked for your vehicle.
The map light bulb, interior door light bulb, and courtesy light bulb are listed as 194 or 7441. These are common interior bulb sizes on the 2006 Toyota Sequoia.
The center high mount stop light bulb size is 194 or 7441. If the third brake light is dim or out, confirm the bulb type and inspect the socket for corrosion before installing a new one.
The front side marker light bulb size is 3157A. This is a separate fitment from the rear side marker light, so do not assume both ends use the same bulb.
The rear side marker light bulb size listed for the 2006 Toyota Sequoia is 7443A. Make sure you match the rear marker position specifically, since it differs from the front side marker bulb.
The fog light bulb position lists 9145 LED, 9140 LED, and 9006 LED. Because aftermarket LED fog light options can vary, confirm the housing and connector style on your vehicle before ordering.
Not always. Trim level, lighting package, market, and body style can affect bulb fitment. The chart on this page is a helpful guide, but checking the installed bulb is the safest way to confirm the exact match.
Halogen bulbs are the most direct replacement for factory-style fitment, while LED upgrades can improve brightness and color but may need additional compatibility checks. For the best result, match the bulb size first and then confirm the LED is suitable for the specific lamp position.