
PIAA 19615 9005 (HB3) Xtreme White Plus
$64.57
Buy on Amazon →
Used for: Headlight Bulb High Beam, Daytime Running Light Bulb
Used for: Headlight Bulb Low Beam
Used for: Back Up Reverse Light Bulb
Used for: Brake Light Bulb, Tail Light Bulb Outer
Used for: License Plate Light Bulb, Map Light Bulb
Used for: License Plate Light Bulb, Map Light Bulb
Used for: Parking Light Bulb, Turn Signal Light Bulb Front
Used for: Side Marker Light Bulb Front
Used for: Side Marker Light Bulb Rear
Used for: Tail Light Bulb Inner, Interior Door Light Bulb
Used for: Tail Light Bulb Inner, Interior Door Light Bulb
Used for: Turn Signal Light Bulb Rear
Used for: Trunk or Cargo Area Light
This page helps you find the correct bulb sizes for the 2007 Toyota Sienna by lighting position, so you can match the right bulb before you buy. Whether you are replacing a headlight, tail light, reverse light, or interior bulb, checking the bulb chart first can save time and avoid fitment mistakes.
The 2007 Toyota Sienna uses a mix of halogen, incandescent, and LED lighting depending on the location. Because trim level, market, and lighting package can change the setup, it is smart to verify each bulb by position rather than assuming every Sienna uses the same part.
For best fitment, compare your vehicle’s trim and lighting package with the bulb list on this page, especially if your Sienna has factory options or a non-U.S. market configuration. Some positions may use halogen bulbs while others may be LED or a specific replacement style, and aftermarket conversions can change the required bulb type. Before ordering, it is a good idea to remove the installed bulb and check the base and markings, since even the same model year can have differences. This is especially important when replacing headlights, brake lights, and exterior signal bulbs, where the wrong bulb type can affect brightness, warning lights, or proper beam pattern.
The low beam headlight bulb is D2R on this page. If your van has been modified or uses aftermarket headlight parts, confirm the bulb type already installed before buying.
The high beam headlight bulb is 9005. This is one of the most common exterior bulbs to replace, so checking the base and connector before installation is still a good idea.
Yes, the daytime running light bulb is listed as 9005. On some vehicles, the daytime running light and high beam positions may use the same bulb family but operate differently.
The back up reverse light bulb is 921. If only one reverse light is out, it is still wise to replace bulbs in pairs when the other side is older.
The front parking light bulb is 3457A. This same bulb size is also listed for the front turn signal position on this page.
The front turn signal light bulb is 3457A. Make sure the replacement is seated correctly, since signal bulbs can be sensitive to poor contact.
The rear turn signal light bulb is 7440. This is a separate bulb from the rear brake and tail light bulb, so do not mix them up.
The brake light bulb and tail light bulb outer are both listed as 7443R. That makes it important to confirm the exact rear lamp position before ordering.
The inner tail light bulb is 194, 7441. This bulb is also used in some interior and license plate positions on the page, so always match the location carefully.
The license plate light bulb is 168, 917. Either bulb size may appear in the chart, so verify the existing bulb style before purchase.
The map light bulb is 168, 917, and the interior door light bulb is 194, 7441. These are different positions, so check the socket and bulb markings before replacing them.
The center high mount stop light bulb is LED. Because LED assemblies can vary, it is especially important to inspect the existing unit if you are replacing or upgrading it.
No. Trim and lighting package can vary by market and body style, so the exact bulb setup may differ. Use this page as a position-by-position guide and verify the installed bulb when possible.