
PIAA 19615 9005 (HB3) Xtreme White Plus
$64.57
Buy on Amazon →
Used for: Headlight Bulb High Beam, Daytime Running Light Bulb
Used for: Headlight Bulb Low Beam
Used for: Back Up Reverse Light Bulb
Used for: Brake Light Bulb, Tail Light Bulb Outer
Used for: License Plate Light Bulb, Map Light Bulb
Used for: License Plate Light Bulb, Map Light Bulb
Used for: Parking Light Bulb, Turn Signal Light Bulb Front
Used for: Side Marker Light Bulb Front
Used for: Side Marker Light Bulb Rear
Used for: Tail Light Bulb Inner, Interior Door Light Bulb
Used for: Tail Light Bulb Inner, Interior Door Light Bulb
Used for: Turn Signal Light Bulb Rear
Used for: Trunk or Cargo Area Light
This 2009 Toyota Sienna bulb size guide helps you verify the correct bulb by lighting position, so you can replace exterior and interior lamps with more confidence. Whether you are changing a headlight, a tail light, or a small cabin bulb, matching the bulb to the exact location is the best way to avoid fitment mistakes.
The 2009 Toyota Sienna uses different bulb types depending on the lamp position, and some listings can vary by trim, market, or body style. Use this page to compare the bulb chart for each lighting point on your van, including headlights, brake lights, turn signals, reverse lights, license plate lights, and interior lamps.
Fitment can change with trim level, lighting package, and whether your Sienna uses halogen or HID-style components in a given position. Some owners also upgrade to LED bulbs or use aftermarket conversion kits, but those changes may affect beam pattern, polarity, heat, or warning issues. Before buying, check the bulb already installed in your vehicle and compare it with the chart here, especially if the van has been modified or if a previous owner replaced factory parts.
The listed low beam bulb size is D2R. This is the type shown for the 2009 Toyota Sienna low beam headlight position on this page.
The high beam bulb size is 9005. This same bulb size is also listed for the daytime running light position on this vehicle.
The daytime running light bulb size is 9005. If you are replacing both sides, make sure you match the exact bulb type for each lamp housing.
The back up reverse light bulb size is 921. This is the bulb listed for the rear reverse lamp position on the 2009 Toyota Sienna.
Both the front parking light and front turn signal are listed as 3457A. That means the same bulb size is used for those front positions on this page.
The rear brake light bulb size is 7443R. The outer tail light bulb is also listed as 7443R, so check the exact lamp position before ordering.
The rear turn signal bulb size is 7440. This is separate from the rear side marker and brake light bulb listings.
The rear side marker light bulb size is 7443A. Be sure not to confuse it with the rear turn signal or brake light bulb sizes.
The license plate light bulb sizes listed are 168 and 917. Either may appear depending on the specific lamp setup, so verify the installed bulb before purchase.
The map light bulb sizes are 168 and 917, and the interior door light bulb sizes are 194 and 7441. These are interior fitments, so the correct size depends on the exact location.
No. The inner tail light bulb is listed as 194 and 7441, while the outer tail light bulb is listed as 7443R. Always match the bulb to the specific tail lamp section.
The trunk or cargo area light bulb is DE3022. This is the bulb listed for the rear interior cargo lamp position on the 2009 Toyota Sienna.
Yes, many owners do, but LED replacements can behave differently from factory halogen bulbs. Check fitment, brightness, polarity, and any heat or warning-light concerns before installing LED bulbs.
Because trim and lighting package differences can change the correct bulb in some positions. Checking the installed bulb helps confirm the exact fit, especially if the vehicle has aftermarket parts or previous repairs.