
Marsauto M1C H11 LED Fog Light Bulbs, 30000LM 6000K Cool ...
$17.99
Buy on Amazon →
Used for: Fog Light Bulb Front
Used for: Fog Light Bulb Front
Used for: Headlight Bulb High Beam
Used for: Headlight Bulb Low Beam
Used for: Back Up Reverse Light Bulb
Used for: Daytime Running Light Bulb
Used for: License Plate Light Bulb
Used for: License Plate Light Bulb
Used for: Parking Light Bulb, Side Marker Light Bulb Front
Used for: Parking Light Bulb, Side Marker Light Bulb Front
Used for: Side Marker Light Bulb Rear
Used for: Turn Signal Light Bulb Front, Turn Signal Light Bulb Rear
Used for: Dome Light Bulb, Map Light Bulb, Trunk or Cargo Area Light
Used for: Glove Box Light Bulb
This page helps you verify the bulb sizes for the 2012 Mitsubishi Outlander by lighting position, so you can match the correct replacement before you buy. Whether you are changing a headlight, interior lamp, or license plate bulb, checking the exact location first can save time and avoid ordering the wrong part.
The 2012 Outlander uses a mix of halogen, HID, and LED lighting depending on trim and market. That means the bulb type can vary between exterior positions and even between similar-looking trims, so it is smart to confirm the fitment for each lamp on your vehicle before starting the replacement.
For best results, compare the bulb chart with the actual lamp on your Outlander, since trim package, body style, and lighting options can change the correct fitment. Some positions use standard halogen bulbs, while others may be LED or HID from the factory, and aftermarket LED conversions may require different bulb shapes, adapters, or resistors to work properly. If you are replacing a bulb that is hard to identify, remove the old bulb and check the base and markings before ordering a new one.
The low beam headlight bulb listed for the 2012 Mitsubishi Outlander is D2S. This is an HID-style bulb, so make sure your vehicle is equipped with the same setup before purchasing a replacement.
The high beam headlight bulb is 9005. If you are replacing both sides, it is usually a good idea to change them in pairs so the light output stays even.
The front turn signal bulb is 7440A. This position can be easy to confuse with other 7440-family bulbs, so confirm the socket and bulb markings before buying.
The rear turn signal bulb is also listed as 7440A. Even though the front and rear turn signals use the same bulb size here, always verify the lamp housing because trim and market differences can affect fitment.
The brake light bulb is listed as LED, and the tail light bulb is also listed as LED. Because these are factory LED positions, the replacement approach may be different from a simple halogen bulb swap.
The center high mount stop light bulb is listed as LED. If that lamp is not working, the repair may involve the full LED assembly rather than a standard replaceable bulb.
The license plate light bulb is listed as 168 or 917. Either designation may appear depending on the bulb style or catalog, so check the existing bulb and socket before ordering.
The dome light, map light, and trunk or cargo area light are all listed as DE3175. That makes interior bulb replacement easier, since the same bulb size is used in several cabin locations.
The glove box light bulb is 2721. This is a small interior bulb, so handle it carefully and avoid touching the glass if you are using a halogen replacement.
The front fog light bulb is listed as H11 LED or H16 LED. The correct choice can depend on trim and market, so check the installed bulb and connector style before purchasing.
The daytime running light bulb is listed as 1156. Some vehicles may have different DRL setups by market, so confirm the actual lamp configuration on your Outlander.
Yes, both the parking light bulb and the front side marker light bulb are listed as 2825 or 98. This shared fitment can be helpful if you want to replace both sides at the same time.